Foreword: This technical requirement belongs to one of the series of energy-saving certification technical requirements. In order to implement the "Energy Conservation Law of the People's Republic of China", carry out energy conservation certification, save energy, protect the environment, improve the energy efficiency of high-pressure sodium lamp ballasts, and guide enterprises to make progress in energy-saving technologies, this technical requirement is specially formulated. This technical requirement is based on the current status of the production and use of ballasts in China, and refers to similar foreign standards. The safety and performance requirements of high-pressure sodium lamp ballasts applicable to this technical requirement shall comply with GB14045-1993 "General requirements and safety requirements for ballasts for discharge lamps (excluding tubular fluorescent lamps)", GB/T15042-1994 Performance requirements for ballasts for sodium bulbs, CCEC/T07.2-2001 "General requirements, safety requirements and performance requirements for AC electronic ballasts for high-pressure sodium bulbs", electromagnetic compatibility requirements shall comply with GB17625.1-1998 "Low-voltage electrical And the harmonic current limit issued by electronic equipment (input current per phase of equipment ≤ 16A) and GB17743-1999 "Limitations and Measurement Methods of Radio Disturbance Characteristics of Electrical Lighting and Similar Equipment". This technical requirement is proposed and managed by the China Energy Conservation Product Certification Management Committee (CCEC). This technical requirement is mainly drafted by: China Energy Conservation Product Certification Center, National Electric Light Source Quality Inspection Center (Beijing), and National Electric Light Source Quality Inspection Center (Shanghai). The main drafters of this technical requirement: Wang Ruohong, Zhao Yuejin, Chen Zhitian, Cha Yuedan, Yu Anqi. 1 Scope This technical requirement specifies the energy-saving evaluation value, test method and inspection rules for ballasts for high-pressure sodium bulbs. This technical requirement is applicable to independent magnetic ballasts and electronic ballasts (hereinafter referred to as high-pressure sodium lamp ballasts) used in 220V, 50Hz AC power supply, high-pressure sodium lamps with nominal powers of 70W~1000W. 2 Reference Standards The provisions included in the following standards constitute provisions of this technical requirement by reference in this technical requirement. The versions shown are valid at the time of publication of this technical requirement. All standards will be revised and parties using this technical requirement should explore the possibility of using the latest version of the following standards. GB14045-1993 General requirements and safety requirements for ballasts for discharge lamps (excluding tubular fluorescent lamps) GB/T15042-1994 Ballast performance requirements for high-pressure sodium lamps CCEC/T07.2-2001 AC electronic ballasts for high-pressure sodium bulbs General requirements, safety requirements and performance requirements 3 Definitions The following definitions are used in this technical requirement. 3.1 High-pressure sodium lamp ballast energy efficiency factor (BEF) ballast efficacy factor The parameter that evaluates the energy efficiency level of the high-pressure sodium lamp ballast and lamp combination. This parameter is the ratio of the ballast factor of the high-pressure sodium lamp ballast to the line power. 3.2 High-pressure sodium lamp ballast energy-saving evaluation value The evaluation values ​​of energy conservation for ballasts evaluation of high-pressure sodium lamp ballast energy-saving level of the lowest ballast high-pressure sodium lamp energy efficiency factor value. 4 Product Classification 4.1 High-pressure sodium lamp ballasts are divided according to their working principle: a) high-pressure sodium lamp magnetic ballast b) high-pressure sodium lamp electronic ballast 4.2 high-pressure sodium lamp ballast according to the nominal power of the lamp is divided into: a) 70W b) 100W c) 150W d) 250We) 400W f) 1000W 4.3 Division of product series 4.3.1 High-pressure sodium lamp magnetic ballast: according to the same model and the same structure type (including silicon steel sheet type, shape, winding method, wiring The method should be the same), but the specifications can be used as a series. 4.3.2 High-pressure sodium lamp electronic ballast: according to the same model, and the same electronic circuit structure diagram, but the specifications can be used as a series. 5 Technical requirements 5.1 Safety requirements The safety requirements for high-pressure sodium lamp magnetic ballasts shall comply with the relevant provisions of GB14045. The safety requirements for high-pressure sodium lamp electronic ballasts shall comply with the relevant provisions of CCEC/T07.2-2001. 5.2 High-pressure sodium lamp ballast energy efficiency factor High-pressure sodium lamp ballast energy efficiency factor (BEF) according to formula 5.3 High-pressure sodium lamp ballast energy-saving evaluation value The high-pressure sodium lamp ballast energy efficiency factor should not be less than the provisions of Table 1. 5.4 Line Power Factor High-pressure sodium lamp Inductance ballast line power factor shall comply with the provisions of Section 5.8 of GB/T15042. 5.5 Durability The heat resistance of the high-voltage sodium lamp inductive ballast windings shall comply with the provisions of 5.2.7 of GB 14045. The durability of the high-pressure sodium lamp electronic ballast shall comply with the provisions of Clause 19.12 of CCEC/T07.2, and the special requirements shall be 65 °C for the 200h continuous working experiment. 5.6 When the ballast of the high pressure sodium lamp ballast and the reference lamp are stable under the rated voltage, the lumen coefficient of the inductor and electronic high pressure sodium lamp ballast is not less than 0.90. 5.7 Output power and current High-pressure sodium lamp magnetic ballasts shall comply with the provisions of Section 5.5 of GB 15042. 5.8 Abnormal state (performance) The abnormal state (performance) of the high-pressure sodium lamp electronic ballast shall comply with the provisions of Clause 19.11 of CCEC/T07.2.
1 2 Next Page
1 2 Next Page
Lighted Stop Signs,Bus Destination Sign,Advertising Lamp Cases
Bus Stop Shelter Co., Ltd. , http://www.ningboqixin.com